Zeta Alarm Systems Infinite 8 Manual de instalación descargar pdf (Pagina 26)

INFINITY ID2 INSTALLATION MANUAL. Software Versions: PANEL O.X-R8629 & LOOP O.J-R8624

Approved Document No: GLT-211-7-1

Issue 1.0 Author: MG Date: 22/1/2013 PAGE 25

15.2 Viewing device status

On the ID2, all Zone devices can be viewed from Main Menu, or viewed & edited from Engineer Menu 1.

Enter Engineer menu 1 as described above, and select option 1

(ID Device)

The following screen is shown

The screen is divided into the following sections:-

Configured Device Type

This shows the Device that was at this address during

the last loop configuration.

There are 7 possibilities for this:-

Optical, Ion, Heat, Call-Pt, Sounder, I/O Unit,

Zone Mon

Device Status

This is the current status of the device. It will show one of

the following values:-

Normal, Fault, Alarm or Prealarm

Fault Description

If the device is in a fault condition, a description of the

fault will appear here. It will show one of the following

messages:-

FAULT

MEANING

Changed

The device had been changed with one of a different type since last configuration. The message

will flash between Changed, and the new type of device seen (eg. Ion).

Missing

The device is not communicating (ie removed , damaged or Address setting changed)

Det Rmvd

A Detector has been removed from a sounder base

Side A Only

There is a break in the cable, and the device is only seen from Side A – Loop Mode Only

Side B Only

There is a break in the cable, and the device is only seen from Side B – Loop Mode Only

2-ADDR

Two devices have the same ID switch setting

No message

This device is signalling an internal fault by returning a value of less than 8.

Device Label

This is the 20 character description of the device location

entered by the installer. To change this Press Enter button

to activate the cursor.

Device Identification

This is the Zone and address of the device. This is

how the device will probably be referred to on the

system drawings.

15.3 Locating a device

From the ID device screen, it is possible to send commands to individual

devices to start their sounder, or to turn on their alarm LED / Flasher.

Select the Zone and ID for the device to be checked.

If the device is a Call point or I/O Unit, its LED can be turned on by pressing

Button 4. A star will appear in the top right hand corner to show that the LED has

been lit on this device. Press again to turn off.

If the device is an ID2 Sounder base with a detector fitted, or a stand alone sounder,

the sounder can be started by pressing the GENERAL TEST button. The Outline

sounder Symbol turns solid to show that the Sounder is active. Press again to turn off.

Similarly their Flasher can be started by pressing button 4. Press 4 again to turn off.

The sounder and flasher can both be activated if required. (Press General test, then 4)

Scrolling to another device or exiting the menu will automatically turn the LED or sounder/flasher off.

Call-Pt

Normal

Front Door

Zone:01 ID:04

Call-Pt

Normal

Front Door

Zone:01 ID:04

Call-Pt 

Normal

Front Door

Zone:01 ID:04

SndSmoke Det Rmvd

FAULT

Fl 3 Bedroom 303

Zone:01 ID:05

SndSmoke 

Normal

Fl 3 Bedroom 303

Zone:01 ID:05

SndSmoke 

Normal

Fl 3 Bedroom 303

Zone:01 ID:05

Optical 

Analog: 25 Normal

Fl 3 Bedroom 303

Zone:01 ID:05

SndSmoke *

Normal

Fl 3 Bedroom 303

Zone:01 ID:05

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 35 36

Comentarios a estos manuales

Sin comentarios

Zeta Alarm Systems Infinite 8 Manual de instalación Pagina 26

Comentarios a estos manuales