Zeta Alarm Systems Infinite 8 Manual de instalación Pagina 3
- Pagina / 36
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
INFINITY ID2 INSTALLATION MANUAL. Software Versions: PANEL O.X-R8629 & LOOP O.J-R8624
Approved Document No: GLT-211-7-1
Issue 1.0 Author: MG Date: 22/1/2013 PAGE 2
15 VIEWING PANEL INFORMATION ..................................................................................................................... 24
15.1 Menu Structure ....................................................................................................................................... 24
15.2 Viewing device status .............................................................................................................................. 25
15.3 Locating a device ..................................................................................................................................... 25
15.4 Using the event log ................................................................................................................................. 26
16. THE FIRE ALARM CONDITION ........................................................................................................................ 27
16.1 Viewing a fire alarm event ...................................................................................................................... 27
16.2 Viewing Faults during a fire alarm condition .......................................................................................... 27
16.3 Viewing Zone Disablements during a fire alarm condition ..................................................................... 27
16.4 Viewing Device Disablements during a fire alarm condition .................................................................. 27
16.5 Viewing Zones in Test Mode during a fire alarm condition .................................................................... 27
17. DISABLEMENT ................................................................................................................................................ 28
17.1 Zone disablement ................................................................................................................................... 28
17.2 To programme zone (or sounders) as disabled ....................................................................................... 28
17.3 Device disablement ................................................................................................................................. 29
17.4 Viewing disablements ............................................................................................................................. 29
17.4.1 VIEWING DISABLED ZONES ............................................................................................................. 29
17.4.2 VIEWING DISABLED DEVICES ........................................................................................................... 29
18. TEST MODE .................................................................................................................................................... 30
18.1 Why use test mode ................................................................................................................................. 30
18.2 To programme zone in test mode ........................................................................................................... 30
18.3 To program sounder circuits in test mode .............................................................................................. 30
19. GENERAL FAULT FINDING .............................................................................................................................. 31
19.1 Common fault ......................................................................................................................................... 31
19.2 Zone contents fault finding ..................................................................................................................... 31
19.3 Zone faults .............................................................................................................................................. 31
19.4 Supply faults ............................................................................................................................................ 32
19.5 Earth faults .............................................................................................................................................. 32
19.6 Double address ....................................................................................................................................... 32
19.7 System fault ............................................................................................................................................ 32
20.1 Standby battery calculation .................................................................................................................... 33
20.2 Device Values for Battery calculation ..................................................................................................... 33
20.3 Example battery calculation .................................................................................................................... 33
21. PCB TERMINATION CONNECTIONS. ............................................................................................................... 34
22 SPECIFICATIONS ......................................................................................................................................... 35
22.1 Enclosure specifications .......................................................................................................................... 35
22.2 Electrical specifications .......................................................................................................................... 35
- INSTALLATION MANUAL 1
- 4 USING THIS MANUAL 7
- 4.1 Equipment guarantee 7
- 6.2 First Fix 10
- 6.2.3 PLANNING CABLE ENTRY 10
- 7 ZONE WIRING 13
- NOTE: THE NC CONTACT 16
- IS OPEN WHEN THERE IS 16
- NO FAULT 16
- 10. FIELD DEVICE TERMINATION 17
- 10.1 Terminating the wiring 17
- ID2 PANEL ID2 REPEATER 18
- 15 VIEWING PANEL INFORMATION 25
- 15.1 Menu Structure 25
- 15.2 Viewing device status 26
- 15.3 Locating a device 26
- 17. DISABLEMENT 29
- 17.1 Zone disablement 29
- 17.3 Device disablement 30
- 17.4 Viewing disablements 30
- 18. TEST MODE 31
- 18.1 Why use test mode 31
- 19. GENERAL FAULT FINDING 32
- 19.1 Common fault 32
- 19.3 Zone faults 32
- 22 SPECIFICATIONS 36
© 2020, manymanuals.es. Todos los derechos reservados | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales