Zeta Alarm Systems Infinite 8 Manual de instalación descargar pdf (Pagina 28)

INFINITY ID2 INSTALLATION MANUAL. Software Versions: PANEL O.X-R8629 & LOOP O.J-R8624

Approved Document No: GLT-211-7-1

Issue 1.0 Author: MG Date: 22/1/2013 PAGE 27

16. THE FIRE ALARM CONDITION

16.1 Viewing a fire alarm event

The way the ID2 panel shows fire alarm information has been changed slightly from previous versions of the

panel. The LCD screen text has been altered to show the first & last zone entering the alarm condition.

For Example, a first alarm on a system will bring up the display:

This Means there is a fire alarm condition. It is the first (and only) alarm that has

Occurred (Fire 1 of 1) The device signalling alarm is in the Manager`s office, and

It is address 001 in zone 01.

If a second fire then occurs in say zone 2, the system would display:

The bottom 2 lines will still show the details of the first alarm (Press Prev or Next to

Display information about the second alarm). The top right hand corner shows the

first zone that gone into alarm, and the last NEW zone that has gone into alarm. Note

that the numbers in the top left corner (1 of 2) is the number of DEVICES in alarm,

not the number of zones in alarm. The ZONAL LEDS will indicate the number of

zones in the alarm condition.

So for example, if there was a third alarm, this time from zone 1 again, the right hand

corner would continue to show First alarm ZONE 1, Last alarm ZONE 2. This allows

the fire brigade to see the spread of the fire.

Because of this, if there are multiple alarms, they are grouped by zone, so scrolling to

review alarms would show all alarms in the first zone in alarm , then all alarms in the

second zone that went into alarm etc. To view the alarms chronologically, the event log must be used.

16.2 Viewing Faults during a fire alarm condition

In the event of multiple alarms, and multiple faults on the system at the same time, the LCD screen will give

priority to alarm events. The screen will show the first alarm, and the Prev/Next scroll buttons will cycle through

alarm events only.

The LEDs will show general fault information. To show fault event details on the LCD screen, press the

CANCEL button. Prev & next will now scroll through the faults. Press cancel to return to viewing the fire alarm

information. (If the panel is left viewing a fault, after a short period of inactivity, the panel will revert to the fire

alarm display)

16.3 Viewing Zone Disablements during a fire alarm condition

Zone disablements are indicated by a LED for each zone.

If no individual devices are disabled, then by pressing the GENERAL DISABLEMENT button and the

disablement SELECT button, information about zone disablements and the number of individually disabled

devices per zone can also be viewed on the LCD.

If one or more devices are disabled, then when the GENERAL DISABLEMENT button is pressed, the screen will

display the options as shown in section 17.4. Press 1 to select zone disablements, and then continue as per the

paragraph above.

16.4 Viewing Device Disablements during a fire alarm condition

To view individual device disablements during an alarm condition, press the GENERAL DISABLEMENTS button,

and the screen will display the options as shown in section 17.4. Press 2 to select device disablements, and

press the Next button to scroll through all the disabled devices.

16.5 Viewing Zones in Test Mode during a fire alarm condition

On the ID2 panel, zone test mode is indicated by a LED for each zone, so LCD screen access is not required.

FIRE First Z01

1 of 1

Managers Office

Zone:01 ID:001

FIRE First Z01

1 of 2 Last Z02

Managers Office

Zone:01 ID:001

FIRE First Z01

2 of 2 Last Z02

Kitchen

Zone:02 ID:017

FIRE First Z01

1 of 3 Last Z02

Managers Office

Zone:01 ID:001

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 34 35 36

Comentarios a estos manuales

Sin comentarios

Zeta Alarm Systems Infinite 8 Manual de instalación Pagina 28

Comentarios a estos manuales